Complete shallow bowl 190mm gloss black headlight unit.

Fits Le Mans 1 headlamp cowling FAA99575. Supplied complete with bulb and three short wires (without connectors). NB mounting holes will need drilling out to 10mm if fitting T3 type indicator stems. Neutral beam pattern and not E Marked

 This part is due back in stock soon, call 01484 841395 to reserve yours

Complete shallow bowl 193mm satin black LED headlight unit. Bright, neutral beam pattern will pass an MOT and illuminates the road much better than a halogen unit. Classic looks suit models from the Le Mans 1 to the V9

Fits Le Mans 1 headlamp cowling FAA99575. Also perfect for custom builds, cafe racers and specials. NB mounting holes will need drilling out to 10mm if fitting T3 type indicator stems. Neutral beam pattern and not E Marked.
Tried and tested on our bikes at Gutsibits

 Availability varies on this part, check availability

Replica fuse box cover with clear lid and securing screw.

 This part is due back in stock soon, call 01484 841395 to reserve yours

 17743000 GU17743000 17 74 30 00
 1774 3000 1774.3000 17.74.30.00

Permanent replacement for unreliable condensers. This capacitor replaces both condensers with a single unit that should never need to be replaced

Earths through supplied bracket, can be mounted inside distributor. Fit and forget reliability. 1 required

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14715433 GU14715433 14 71 54 33
 1471 5433 1471.5433 14.71.54.33

Red NGK spark plug resistor cap with rubbers

Also known as suppressor cap

 Sorry, this part is no longer available.

LD05F

Complete 12v 300w alternator for Saprisa charging systems

No longer in production

 Sorry, this part is no longer available.

 28712400 GU28712400 28 71 24 00
 2871 2400 2871.2400 28.71.24.00

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 12 volt coils and can be used to replace points or Bosch electronic ignition on models with Bosch charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. We recommend fitting Dyna coils ELA14101 with this kit. If you wish to combine this kit with uprated charging system ELA00502 you will need to make or source longer studs (M5 x 67mm x 2) for pickup, and longer centre bolt (M8 x 58mm wasted). See ACA50001 for distributor blanking plate if required

 This part is due back in stock soon, call 01484 841395 to reserve yours

Alternator upgrade kit for Bosch systems containing stator windings, wound rotor and replacement diode board. The superior design alternator has an output up to 300% greater than the original Bosch system. You may wish to fit a plastic alternator spacer ENA18150 if your model does not have one of these already (to improve cooling of the alternator). You will need front crank seal ENA90428 (Bosch seal) if you wish to fit this to a bike with a Saprisa charging system. This kit reuses your existing Bosch regulator and stator plate with brush holder, see ELA29703 for a replacement regulator and ELA17452 for brush holders.

• Outputs 600W @5000 RPM
• Supplied with rotor removal tool
• For tapered crankshafts

1. Remove stator and rotor using the supplied rotor removal tool
2. Remove the old stator windings from the stator plate
3. Solder in the new stator widing wires to the connection block on the stator plate and reconnect the
4. Mount the replacement diode board, this should be protected from the weather but cooled by passing air
5. Connect up the system as follows: Terminals U,V and W take the three yellow wires which should be connected to the stator plate block; Y goes to Y on the stator plate; The brown wires go to earth (we recommend using some earth sleeve on these if possible); Red goes to the battery positive terminal; regulator wiring remains as before (D+ to diode board, D- to earth and DF to brush holder)
6. Check charge warning light is working (earth DF wire at stator to check bulb function)
7. Turn motor over by hand to ensure everything is seated correctly, there should be an air gap between the stator windings amd rotor
Fit alternator cover and spacer

 This part is available by special order, request a quote

Round 12v two pin flasher relay with warning buzzer, reduces risk of indicators being left on.

Includes mounting rubber

 This part is due back in stock soon, call 01484 841395 to reserve yours

 17750520 GU17750520 17 75 05 20
 1775 0520 1775.0520 17.75.05.20

Brakelight switch banjo bolt

See BRA01004 and BRA01014 for alternative universal stop light switch. Also known as Guzzi ref. 06261020, 000037891, 800037891, 079654114, 14657050

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14657959 GU14657959 14 65 79 59
 1465 7959 1465.7959 14.65.79.59